HIGH POWER INFRARED SINGLE MODE OPTICAL PM FIBER AMPLIFIERS up to 50W in IR
ALS-IR-AMP series are design to provide solutions in the atom cooling domain when specific narrow spetral line width are needed.
Azur Light Systems opens the available solutions either providing the full laser source or only the high power optical stage amplifier.
Most common central wavelengths:
Almost all the central wavelenghts are available from 1020 nm to 1090 nm, only the max output power may change below 1020 nm and above 1090 nm
ALS-IR-AMP series is a range of high power, high brightness Single frequency All Fiber based MOPA Technology infrared laser amplifiers. We design standard and custom optical laser amplifier inside the wide range of wavelength available from Yb3+ fiber based laser technology.
Based on patented technology and major advances in fiber and system design, our fully integrated laser amplifier platform offers diffraction limited output powers in excess of 50 W (depending on central wavelength).
Our unique technology can power up CW Laser seed optical wave without degrading spectral line width even for ultra narrow line width <1kHz. without line broadening
The optical laser seed input FC/APC request only 15mW (for weaker signal contact us)
A full spectral control of the output is possible with linewidths down to less than 1kHz (single longitudinal mode) and a drift of the central wavelength is only laser seed dependant.
The free space coolerless output head deliver the amplified optical light wave without additional noise. Our low noise technology has demonstrated that the output RIN profile is equal or better than the laser seed noise profile.
Power sharing over several output ports (2, 4, 8, 16...) is available as an option.
Keywords: High power, Low noise, Single frequency, Beam quality, Coolerless free space laser head, Maintenance free, Fast delivery, Optical amplifier.
A wide range of applications
High power high brightness pumping : Yb-doped crystal and glass lasers clic for this application page
Parallel pumping : Er fiber and amplifiers clic for this application page
Atoms traping and laser cooling clic for this application page
Non-linear frequency generation in the visible clic for this application page
____________________________________________________________________________________________________
Specifications
Download the datasheet here
|
High Power Standard optical Amplifiers for FC/APC external seeder |
Unit |
|||
|
Wavelength domains (1) |
975_980 |
1025_1052 |
1055_1085 |
nm |
|
Output power |
5, 10, … |
5, 10, …, 50 |
W |
|
|
Output power Tunability |
1 to 100 (10 to 100 recommended) |
% |
||
|
Beam quality |
M² < 1.1 |
- |
||
|
Beam diameter « free space » |
1.1 ±10% |
mm |
||
|
Beam divergence |
< 0.4 |
mrad (FW@1/e^2) |
||
|
Spatial mode |
TEM00 |
- |
||
|
Input optical power |
15 to 150 |
mW |
||
|
Power stability |
< ± 0.2 (short term) |
% % |
||
|
Noise [100Hz - 10MHz]: |
Seeder dependent |
% rms |
||
|
Frequency stability |
Seeder dependent |
|||
|
Output polarization |
Polarized > 99.9:1 |
- |
||
|
Pointing stability |
< ± 0.5 |
µrad/°C |
||
|
Output(2) |
Free space laser head |
- |
||
|
Laser control |
Multi-turn potentiometer, Touchscreen, Analog voltage |
- |
||
|
Supply requirements |
90-240V/50-60Hz |
- |
||
|
Electrical power consumption |
200<…<500 |
W |
||
|
Cooling |
Air cooled |
- |
||
(1): wavelength range: the effective standard useable spectral domain is define at +/- 4nm from one requested central wavelength.
Extended wavelength range are available on demand.
(2): other on demand
Nota: For our standard 50W devices we include in the coolerless laser head a high power IR isolator to prevent damages that may occur from an intense back reflection, therefore the available power is >45W.